Posts

Week 17: Submission of hardcover

Image
Title: Submission of hardcover  Objective: to complete the submission Content :  In this week of the semester, I have done the report hardcover and ready to submit. In the name of Allah s.w.t the most gracious and the most merciful. Alhamdulillah, all praise to Allah S.W.T because of His blessing and His permission will allow me for completing this final year project thesis. In preparing this final year report, I dealt with people and they have a great contribution towards my understanding and thought. I would like to express my gratitude, especially to my supervisor Madam Norhaslinawati for never giving up to guide and for the encouragement, guidance, and enthusiasm given throughout the completion of this proposal and willing to spend her precious time to give some ideas and suggestion toward this project. Last but not least to my beloved family on their support to finish the project,  and also to my friends who provide ...
Post a Comment
Read more

Week 16: Plagiarism check for the report

Image
Title: Plagiarism check for the report Activity:  Do correction if greater than 20% ObjeCtive: to finish the report and follow the format Content: The report has been check by Turnitin software Result and analysis:  The result from Turnitin software. Conclusion   :      By the end of this week, I finished to complete my plagiarism and printed out the result. 
Post a Comment
Read more

Week 15: Draft report

Image
Title: Draft report Objective: to submit a draft of the final year project report Progress:  For this week, I need to do some analysis on the result based on experiment and complete the final year project report. Content: Conclusion:  The report has been completed and will be sent to the supervisor for check and comment.
Post a Comment
Read more

Week 14: Final Year Project Presentation Day

Image
Title: Final Year Project Presentation Day Objective:  To present the poster and demonstrate the final year project.      Method: Present the poster and slide to the assessor, demonstrate the hardware project, answer questions and being evaluated by the assessor. Progress:  The Final Year Presentation  (FYP 2) took place in the Dewan Gemilang, Unikl British Malaysian Institute (BMI) on 2 May 2018. The presentation started at 8:30 in the morning. I was assigned to two assessors from the FYP committee who are lecturers from the Electrical Section.  Conclusion: Everything went well for the presentation. After the presentation is time to prepare the report
Post a Comment
Read more

Week 13: Making The Presentation's Poster

Image
Title:  Making The Presentation's Poster Objective:  To design the poster for the Presentation day Progress:   This week, I need to design a poster using Microsoft Publisher. The poster needs to include the objectives of the project, project descriptions, methodology, flowchart, results, conclusion, and references.  Results: Part 1 Part 2 Conclusion:     By the end of this week, I finished to design my poster and printed out for the Presentation day.  
Post a Comment
Read more

week 12: Testing and Troubleshooting

Image
Title:  Testing and Troubleshooting Objective:  To test the functionality of my project Progress:                 Last week I tested the function of the Blynk application and the result as desired.  for this week, I need to test the functionality of my project installed in the prototype as shown in the figure below. The prototype of project There are no presences of gas leakage so that the display show “Gas normal” and the exhaust fan is in a turn off situation means the sensor did not receive any signal.  when the gas detected by the sensor. The MQ6 sensor sends data to Arduino and gives the high output to activate the exhaust fans, buzzer and display the “Gas alert” in the LCD display .  Conclusion:                     As the conclusion, by the end of this week, I finally manage to test the prototype and get the result as desire...
Post a Comment
Read more

Week 11: Test the Functionality of the Blynk application

Image
Title: Test the functionality of the Blynk application Objective:  To test the functionality of the final year project. To send data from MQ6 sensor to Blynk application. Progress: First, connect supply to the Arduino. Put the hardware in the closed environment. Switch on hotspot from mobile phone to act as a Wi-Fi for the Wemos D1 to send the data into Blynk apps, and then open Blynk apps in the phone and monitor the data collected from the  sensor MQ6. when gas is detected, Blynk libraries will connect to Blynk server and pair up with any Smartphone. The push notification widgets notify the user by sending the alert message and the location of the incident occurred. Besides, it also sends notification via email. Conclusion:                     As the conclusion, by the end of this week, I finally understand the concept and operation of my project based on Blynk application.
Post a Comment
Read more